INSTALLATION INSTRUCTIONS. SAVER ™ BATH WALLS. MODEL: 2649BW. USE BATH WALL 2649BW WITH BATH TUB 2647.102 or 2647.202. Thank you for selecting American Standard. Mar 14, 2017 Learn how to install the Saver shower doors from American Standard. To begin, identify all the necessary parts using the instructions guideline as a. Free Download Program Illinois Urban Manual Drawings Of Trees.

• INSTALLATION INSTRUCTIONSSAVER™ BATH WALLSMODEL: 2649BWUSE BATH WALL 2649BW WITH BATH TUB 2647.102 or 2647.202Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installedproperly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also besure your installation conforms to local codes.BEFORE YOU BEGIN.Local building codes vary by location. • Installation for use with tub Model# 2647.202The studs should be located as shown to properly support walls. Provide additional studs where illustrated. (below)60'(1524mm)10'(254mm)9-1/4'(235mm)10'(254mm)9-1/4'(235mm)8-1/4'(210mm)12'(305mm)6'(152mm)30'(762mm)8-1/4'(210mm)Installation for use with tub Model# 2647.102The studs should be located as shown to properly support walls. Provide additional studs where illustrated.

• 1INSTALLATION PROCEDURES:If you plan to install a bath/shower door, a 1 x 4 must be installed in the pocket on the back of both side walls.A) Cut one end of the 1 x 4 to 45° as shown. (Fig.1) Then cut the 1 x 4 to a length of 57-1/2'.B) Apply a bead of tub surround adhesive in the pocket of each side wall.

With 45° cut end down and angle facing out,attach board butting up to the top of the pocket. Allow time to cure. • 3Pencil lineA) Apply a bead of tub surround adhesive down each studthat will come in contact with the back panel being sureto stay below the line you marked. Wow Patch 4 3 Mining Bot Gems. You do not need toapply adhesive to the corner studs.B) Lay a bead of sealant along tub ledge.Tub SurroundAdhesivebeadC) Reposition back panel aligned with pencil line and pressfirmly against studs.Sealant4A) • Locate and drill a clearance hole in the center of the top nailing flange and centered on each stud (see arrows as shown).

• A) Apply a bead of tub surround adhesive downeach stud that will come in contact with the sidepanels being sure to stay below the linepreviously marked.C) Align the top nailing flange of each sidepanel with pencil line marked. Press firmly intoplace to ensure proper adhesion to studs.Check alignment with all mating surfaces andreposition if necessary.B) Lay a bead of sealant along side panel matingsurface and tub ledge. • 7Install temporary braces to hold thecenter of the back and side panels tightto the studs for approximately 24 hourswhile adhesive sets. Add cushioningbetween panels and braces to preventscratching the panels.8When installing greenboard, positiondrywall screws above the top nailingflange. If you choose to screwthrough the nailing flange, youMUST drill clearance holes in theflange to avoid cracking/damagingthe flange. • POST INSTALLATION CLEAN-UPRemove all construction debris.

Tile grout can be removed with a wooden popsicle stick or tongue depressor.Do not use wire brushes or any other metal implement on surface.Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent.Stubborn dirt or stains may be removed using granular Spic and Span® mixed with water.Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.